heat-proof plastic-dipped ABS composite eyewash
1. Product introduction
The eyewash adopts advanced temperature control technology to ensure that there will be no high-temperature water source in the eyewash pipe to achieve the purpose of heat protection. When the temperature of the water source on the factory is higher than 30 At , the heat- proof device starts to open with a small flow; when the water source temperature is lower than 28, the heat-proof device is automatically closed. The eyewash is coated with ABS on the outer layer of SS304 material, which can resist the corrosion of various chemicals. It is equipped with a spray part and an eyewash part. It is directly installed on the ground of the factory site and connected to drinking tap water; when chemical substances are splashed When working with the eyes, face or other parts of the body , turn on the spray switch of the composite eyewash to rinse the body or clothing with a large amount of water, or open the eyewash part to rinse the injured eyes and face with a large amount of water. Time>15 min utes; spray water flow:>75.7L/MIN, eyewash/facewash water flow:>11.4L/MIN, eyewash water flow:>1.5L/MIN.
American eyewash standard ANSI/ISEA Z358.1 2014 Emergency Eyewash and Shower Standard
European eyewash standard EN 15154:1/2 2006 and 15154:3/4 2009 Emergency Eyewash and Shower Standard
Australian eyewash standard AS4775-2007 Emergency Eyewash and Shower Standard
optional configuration: The eyewash device can be equipped with sound and light alarm, explosion-proof lighting, DCS connection, timing drainage device, waste water collection enclosure and water curtain, etc.
There is fixed drinking tap water at the application site, if not For a fixed water source, you should choose a portable eyewash
water source pressure requirement: 0.2~0.6 MPa. If the water supply pressure is lower than the above pressure, the customer needs to inform STGSTG. When STGSTG produces the eyewash, it will modify the internal structure of the eyewash to meet the eyewash standard The technology requires
that the eyewash device is dipped with ABS on the outer layer of stainless steel 304, which can resist the corrosion of various chemicals.
The eyewash has a heat-proof function and is suitable for use in areas where the ambient temperature is higher than 38C.
Use water temperature: 16~38. (The temperature value of the water source is solved by the on-site water supply) It is
directly installed on the ground of the work site.
Products are widely used in petroleum, chemical, electronics, electric power, ports and pharmaceutical industries.
3. Performance characteristics: The
use of advanced temperature control technology to ensure that there will be no high temperature water source in the eyewash pipes to achieve the purpose of heat protection.
When the temperature of the water source on the factory site is higher than 30 , the heat protection device starts to open with a small flow; the water source temperature
When the temperature is lower than 28, the heat-proof device is automatically closed. When the water source temperature of the factory is 38, the heat-proof device starts to open with large flow. It is
suitable for areas where the ambient temperature is higher than 38. Use the
water inlet at the position of the spray bar. The heat-proof device is installed in the position of the eyewash part. The entire eyewash device is based on the flow direction of the water source, and there is no dead corner to freeze. At the same time, it also ensures the water quality of the water source is clean and hygienic. The
outer layer of stainless steel SS304 material is coated with ABS, which can resist various chemicals The corrosion is
equipped with a spray system and an eyewash system, which can not only wash the face and eyes, but also wash the chemical substances on the body and clothing. Install directly on the ground of the work site, and connect the drinking tap water with the
outer layer of pipe material SS304. Dip ABS, can resist corrosion of various chemicals, pipe fitting thickness: 3.0mm, pipe fitting thread: NPT
water inlet size: 1-1/4 inches FNPT, this size can be adjusted according to the customer site.
Outlet size: 1-1/4 inch FNPT, the size can be adjusted according to the customer’s site.
Spray water flow rate:> 75.7 L / MIN
wash water flow rate:> 1.5 L / MIN
eyewash / water wash flow rate:> 11.4 L / MIN
washing time:> 15 MIN
water pressure requirements: 0.2 ~ 0.6 MPa
push-handle attached to the luminescent The nameplate is
equipped with an eyewash device and it is luminous and safe.
4. Installation requirements: The
general principle is to
install near the hazardous work area, generally 10 or 15 meters away.
The time to reach the eyewash in a straight line should not exceed 10 seconds . The
must be connected to drinking tap water.
Use water pressure of 0.2~0.6MPa
within the radius of 2 meters of the eyewash, and no non-explosion-proof electri